Loading... Please wait...

How to Make a Quick Release Paracord Bracelet with Shackle

neongreengator.jpg
     Probably the most survival ready bracele there is, the Gator is packed with cord and can completely unravel in under 20 seconds. The Gator paracord bracelet truely is a quick release survival bracelet. Throughout this tutorial I will show you how to make your own quick release paracord bracelet.
 
 
whatyou-llneed.jpg
What You'll Need:
  • 15 ft. of paracord
  • Tape measure
  • Metal Shackle
  • Scissors 
  • Lighter
  • Jig. (Optional) 
  • 15-20 minutes

 

Step 1: Measuring Your Wrist

1. Take a cord, string, or rope and wrap it around your wrist. 

2. Take a marker and draw a line across both pieces like shown in part 2 of the diagram.

3. To make it easier to see, I darkened the marker marks with a photo editing software. You can see what it should look at in part 3 of the diagram.

4. Lay your cord out on a table and measure from line to line. **NOTE: Remember to add 1" to your measurement to get your final measurement.

howtomeasurewrist.png

Step 2: Starting With A Cow Hitch

  • The numbers below correspond to the numbers in the diagram.
  • Find the mid point of your cord, and fold it in half.
  1. Take the loop that is formed at the mid point, and feed it through the shackle.
  2. Locate the 2 end cords.
  3. Feed the 2 end cords through the loop on the other side of the shackle.
  4. It should look like this once completed. 

quickreleasesurvivalbraceletstep1.png

Step 3: Creating Your Inner Cords And Measuring For Wrist Size

  • The numbers below correspond to the numbers in the diagram.
  1. About 7 or 8 inches down your cords, use your finger to wrap the cords around and bring it up past the shackle.
  2. Like shown in part 2 of the diagram, separate your cords into 2 separate "inner cords". PLEASE NOTE: These cords will act as 1 cord each. Notice "inner cord 1" and "inner cord 2". Although they each have 2 cords in them, them act as 1 cord each. 
  3. Take your tape measure or ruler and lay it down next to your setup. Measure from the middle of the "shckle bolt" to the end where to 2 loops are. **NOTE: You must add 1" to your measurement. For example, the wrist for the bracelet below was around 8", so we are measuring this around 9" to end up with the right fit.

quickreleasesurvivalbraceletstep22.png

Step 4: Temporary Step: Taping Ends

We tape the ends to have precise braiding, and a better fit when finished.

  1. Tape both ends of both inner cords.
  2. You are now ready to start your braids.

quickreleasesurvivalbraceletstep3.png

Step 5: Stabilizing The Top Of Your Bracelet To Begin Braiding. Essential Step In Overall Outcome Of Bracelet.

-Make sure it's nice and tight when you begin your first braid.

  1. Place the left cord over both inner cords.
  2. Wrap the same cord around the back of both inner cords back to the left side.
-Make sure it looks like it does in part 2 of the diagram.
-You are now ready for your first Gator braid.

quickreleasesurvivalbraceletstep4.png

Step 6: Completing Your First Gator Braid.

-Please take your time as there is a lot going on in this part of the tutorial. 

-Remember the numbers below correspond to the numbers in the diagram below.

-Please make sure to follow the arrows in the diagram as they will show where the cord goes and whether it goes over or under another cord.

  1. Place the left cord over "inner cord 1" and under "inner cord 2" ending up on the right side with the cord.
  2. Place the right cord under the left cord you just brought over from the left.
  3. Take the same cord and go over "inner cord 2" and under "inner cord 1".
  4. Continue with the same cord up under and through the loop that was formed. Remember to look at the part that corresponds to the number in the instructions.
  5. This is a slightly tightened braid so you can see what it should look like when tightening it yourself. 
  6. Using your fingers, push up on the braid to make sure its tight up against the shackle. 

quickreleasesurvivalbraceletstep5.png

Step 6: Completing Your Second Braid.

-Remember the numbers correspond to the numbers in the diagram.

-Also remember to follow the arrows, as they will help you determine which cord goes where, and if they are going over or under other cords.

  1. Thread your right cord under the "inner cord 2" and over the "inner cord 1".
  2. Thread your left cord over the cord you just brought over to the left.
  3. Continue that same cord under "inner cord 1" an over "inner cord 2".
  4. Continue that same cord up, over and through the loop that was formed. Remember to follow the numbers in the diagram.
  5. When tightening your braid, it should look like this.
  6. A finished, tight Gator braid.

 quickreleasesurvivalbraceletstep66.png

Step 7: This May Happen

  • When your braiding your Gator braids, this may happen to you.
  • The numbers in the diagram correspond to the numbers below.
  1. Your braids may start sliding down the two inside cords of each "inner cords".
  2. Grab onto the to inside cords of each "inner cord" and push up on the braids to correct it.

quickreleasesurvivalbraceletstep7.png

Step 8: Weaving Down To The End

  • Follow the numbers in the diagram. They correspond to the numbers in the instructions.
  • Once you have a descent amount of braids, you can undue the tape.
  1. This is a close up of what your brads should look like.
  2. Close up of Gator braids.
  3. Braid until your left with about a 1/2 inch left.

quickreleasesurvivalbraceletstep8.png

Step 9:  Cutting And Melting The Ends

  • Remember.. Each of the numbers in the intructions, correspond to the numbers in the diagram below.
  1. Using your scissors, cut the leftover cord with about 1/8 inch remaining. Do this for both sides.
  2. Melt each side with the lighter, and using your finger rub the top of it in a circular motionto form the the melted cord, and form a mushroom shape on the end. The mushroom shape will make it so the "Head" of the mushroom will hold in place and not be able to be pulled through. If you have trouble with this, please let us know. We are working on a video to demonstrate this.
  3. It should look like this when finished. Make sure to make the side where you melted the ends the inside of the bracelet against your wrist. This will hide it from view.

quickreleasesurvivalbraceletstep9.png

Putting It On

  1. Slide the 2 end loops over the side of the shackle which has the threads.
  2. Put the bolt on and tighten.
  3. Pull loops back over onto the bolt.

quickreleasesurvivalbraceletstep10.png

 

And You're Done!

Also find this tutorial on Instructables.com here: http://www.instructables.com/id/How-To-Make-A-Quick-Release-Survival-BraceletQuic/

neongreengator.jpg



Recent Updates

Sign up to our newsletter